***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed May 14, 2025 7:37 pm


Board index » Forum Archive

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 1
  [ 15 posts ] 
  Print view Previous topic | Next topic 
Author Message
WalterK
 Post subject:
PostPosted: Fri Jul 08, 2005 2:11 am 
Offline
Koa
Koa

Joined: Sat Jan 15, 2005 7:24 am
Posts: 830
Location: United States
Hi Guys!!
I have been trying to set dot markers on a ebony fretboard and having a lot of fun too!!!
How do you drill holes without chipping the fretboard?
I'm using bradpoint drill bits and going very slow but I still get some chipping of the wood.
Need Help..Please.
Thanks, Walter


Top
 Profile  
 
John Mayes
 Post subject:
PostPosted: Fri Jul 08, 2005 2:27 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jan 08, 2005 3:37 am
Posts: 2670
Location: United States
First name: John
Last Name: Mayes
City: Norman
State: OK
Focus: Build
Status: Professional
I've never had a problem with either a pilot bit or a std. twist bit. Never
chipped out on me. Ebony is good about that.John Mayes38541.4773611111

_________________
John Mayes
http://www.mayesluthier.com
Top
 Profile  
 
John Mayes
 Post subject:
PostPosted: Fri Jul 08, 2005 2:28 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jan 08, 2005 3:37 am
Posts: 2670
Location: United States
First name: John
Last Name: Mayes
City: Norman
State: OK
Focus: Build
Status: Professional
My favorite bits I have are the dewalt pilot bits... although the smaller
ones don't have a pilot

_________________
John Mayes
http://www.mayesluthier.com
Top
 Profile  
 
John How
 Post subject:
PostPosted: Fri Jul 08, 2005 3:00 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jan 03, 2005 7:40 am
Posts: 2694
Location: United States
First name: John
Last Name: How
City: Auburn
State: Ca
Country: USA
I use a 1//4" Forsner bit, it seems to give me a nice flat bottom with no chipping.

_________________
Tickle your guitar daily, and it'll tickle you back.
Top
 Profile  
 
LanceK
 Post subject:
PostPosted: Fri Jul 08, 2005 3:21 am 
Offline
Site Admin
User avatar

Joined: Mon Dec 27, 2004 5:02 am
Posts: 8553
Location: United States
First name: Lance
Last Name: Kragenbrink
City: Vandercook Lake
State: Michigan
Zip/Postal Code: 49203
Country: USA
Focus: Build
Status: Semi-pro
Bradpoint, no problems at all.

_________________
Support the OLF! Bookmark our STEWMAC link Today!
Lance@LuthiersForum.com
Top
 Profile  
 
Jim Watts
 Post subject:
PostPosted: Fri Jul 08, 2005 3:37 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 12, 2005 5:46 am
Posts: 2990
Location: United States
Haven't had that problem, but you might try reinforcing the area with some CA glue prior to drilling.

_________________
Jim Watts
http://jameswattsguitars.com
Top
 Profile  
 
Dave Rector
 Post subject:
PostPosted: Fri Jul 08, 2005 3:50 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Feb 12, 2005 1:07 am
Posts: 2281
Location: Jones, OK
Cheap bradpoint set from Harbor Freight. No problems with them so far.

_________________
Dave Rector
Rector Guitars
Top
 Profile  
 
Brock Poling
 Post subject:
PostPosted: Fri Jul 08, 2005 3:57 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States

Drill it backwards for the first couple of seconds then go forward. That will help with that problem.


_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com
Top
 Profile  
 
Michael Dale Payne
 Post subject:
PostPosted: Fri Jul 08, 2005 4:43 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
[QUOTE=Brock Poling]
Drill it backwards for the first couple of seconds then go forward. That will help with that problem.

[/QUOTE]

good tip Brock. Especialy on old dry ebony I also on ocasions use a sacraficial back-up bord over the Fb. 1/8 thk. shaped to match the FB prior to radiusing. I use small bits of double sided taple to attach it in place and clamp as close as possible each side of the hole to be drilled. This requires a good bit of pre planing and set-up. but the back up board will prevent the ebony from chiping.
Top
 Profile  
 
RussellR
 Post subject:
PostPosted: Fri Jul 08, 2005 5:05 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Jun 16, 2005 10:31 am
Posts: 2103
Location: United Kingdom
I have never had a problem with ebony and use all manner of brad point bits, You could put on some masking tape and drill through it.

Ensure you clean the drill after each hole, though
Top
 Profile  
 
Jerry Hossom
 Post subject:
PostPosted: Fri Jul 08, 2005 5:07 am 
Offline
Cocobolo
Cocobolo

Joined: Fri Apr 15, 2005 11:38 am
Posts: 200
Location: United States
Bit speed may be another issue. There is a tendancy with wood to run too slow, and with metal too fast. Wood likes fast; metal demands slow.


Top
 Profile  
 
RussellR
 Post subject:
PostPosted: Fri Jul 08, 2005 5:10 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Jun 16, 2005 10:31 am
Posts: 2103
Location: United Kingdom
Sorry Walter me again, I just read the post carefully, did you mean you are pushing in the drill press slow or that you are running the drill bit really slow, if it is the later you could be too slow and tearing rather than cutting the wood.

Russell
Top
 Profile  
 
RussellR
 Post subject:
PostPosted: Fri Jul 08, 2005 5:19 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Jun 16, 2005 10:31 am
Posts: 2103
Location: United Kingdom
Sorry just duplicated Jerry, but I can't type too fast Doh


Top
 Profile  
 
PaulB
 Post subject:
PostPosted: Fri Jul 08, 2005 10:20 am 
Offline
Koa
Koa

Joined: Wed Jan 05, 2005 10:43 pm
Posts: 1124
Location: Australia
First name: Paul
Last Name: Burns
City: Forster
State: NSW
Zip/Postal Code: 2428
Country: Australia
Focus: Build
Status: Amateur
Yeah, I agree, you want your drill bit spinning flat-out.
Top
 Profile  
 
Dave-SKG
 Post subject:
PostPosted: Fri Jul 08, 2005 10:41 am 
Offline
Koa
Koa
User avatar

Joined: Wed Dec 29, 2004 5:34 am
Posts: 1906
Location: United States
Hi Walter,
I was chipping out when I drilled too slow. Trying to be super careful and tore the wood instead of drilled. Nothing that some ebony dust couldn't cure . That's beauty of ebony I don't do it by hand any more tho...made a jig and just run it down the drill press as fast as I can! ( Thanks to Sylvan! )Dave-SKG38541.8211342593

_________________
Dave Bland

remember...

"If it doesn't play in tune...it's just pretty wood"
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 15 posts ] 

Board index » Forum Archive

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 46 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com